Measure the opening, not the room
A baby gate fails at the fit stage more often than at the installation stage. Before you compare models, get one number right: the clear width of the opening you want to block. Measure the gap between the two surfaces the gate will press against, not the width of the trim or the room.
The Evenflo Position & Lock Tall and Wide Value Adjustable Baby Gate is built for a broad range of openings. It accommodates widths from 31 in to 50 in (79 cm to 127 cm) and stands 31 in. (79 cm) tall. If your measurement falls inside that window, this gate is a candidate. If it falls outside, look at a different size rather than forcing the fit.
How to take a width measurement you can trust
Do this at the height where the gate will actually sit, since doorways and stair openings are not always square.
- Measure at gate height: Hold the tape between the two mounting surfaces at roughly the height the gate will sit, not down at floor level where baseboards can throw off the number.
- Measure in more than one spot: Take a reading at the top, middle and bottom of the opening. Walls and trim are rarely perfectly parallel, so note the widest and narrowest readings.
- Check both sides of a doorway: For a doorway, measure from each side of the frame. If the two readings differ, plan around the larger one so the gate is not squeezed.
- Write the number down: Keep the smallest and largest readings with you when you compare gates. A single measurement hides the variation that causes a poor fit.
Where the 31 in to 50 in range lands
That range covers a lot of real openings: standard interior doorways, wider hallway entries and some open-plan gaps. The extended height matters too. At 31 in. tall, the gate sits higher than many basic models, which is the point of the Tall and Wide design.
The tradeoff is that this is a value gate intended for basic use. Evenflo describes it as lightweight and larger-sized, perfect in a pinch for easily blocking wider doorways from little ones or pets. If you need a gate for constant daily traffic through a busy hallway, weigh that against the simpler build before you commit.
Position & Lock Tall and Wide at a glance
- Position & Lock Tall and Wide Value Adjustable Baby Gate: Accommodates openings from 31 in to 50 in (79 cm to 127 cm) wide and stands 31 in. (79 cm) tall. These are the two numbers your measurements need to fall inside before anything else matters.

Position & Lock Tall and Wide Value Adjustable Baby Gate - Position & Lock Tall and Wide Value Adjustable Baby Gate: A pressure-mounted baby gate with a simple lift and lock installation that installs and uninstalls with ease. Pressure mounting is why the opening measurement is the deciding factor, and why the gate can be moved between openings.
- Position & Lock Tall and Wide Value Adjustable Baby Gate: A lightweight, larger-sized wood gate intended for basic use, such as easily blocking wider doorways from little ones or pets. Sets honest expectations about build and duty before you buy.
- Position & Lock Tall and Wide Value Adjustable Baby Gate: Available in a Farmhouse Collection color option. Color is the one option to choose at checkout once the size fits.
Measuring for stairs is a different job
For a stair opening, measure the clear width between the two surfaces the gate will press against, exactly as you would a doorway. The supplied information for this gate does not include stair-specific mounting hardware, angle adapters or instructions for angled banisters, so treat a straight, parallel opening as the fit this gate is described for.
If your stair opening involves a banister post, a wall at an angle or a gap that widens toward the bottom, the supplied information does not confirm that this gate covers that setup. Measure it anyway, keep the numbers, and check the specific mounting requirements before you buy rather than assuming a pressure gate will span an irregular opening.
Fit checkpoints before you order
- Width inside 31 in to 50 in: Your narrowest and widest readings should both sit inside the range. A reading at the very edge of the range leaves little margin.
- Height suits the location: The gate is 31 in. tall. Consider whether that height is what you want at this particular opening.
- Opening is straight and parallel: Pressure mounting relies on two opposing surfaces. The supplied information does not describe angled or offset installations.
- Basic use is enough: Evenflo positions this as a value gate for basic use. Match that to how often the gate will be opened and closed.
- You can lift and lock it: Installation is a lift and lock method. Confirm you can reach and operate the gate comfortably from both sides.
What the supplied information leaves open
The supplied product information does not include a maximum wall-to-gate gap, a required pressure setting, extension kits, or care and cleaning instructions. It also does not describe use on stairs beyond the general pressure-mount design. Rather than guess at those details, check the packaging or the manufacturer's instructions for your specific opening before installing.
What the information does settle is the sizing question. Measure the clear opening, compare it to 31 in to 50 in wide and 31 in. tall, and confirm the surfaces are straight and opposing. If all three line up, the Position & Lock Tall and Wide gate is a straightforward, affordable answer for a wide doorway.

